A guide to metal finishes for interiors in Utah

The same panel can look rugged, calm or precious depending on its finish. This guide shows the five finishes we work with most, what each one looks like, where it suits a room and how to look after it. It does not name products or brands, only the surfaces themselves.

Four square metal sample plates side by side: raw, ground with swirl marks, polished and smooth paint ready

Raw

The metal as it comes from the mill, with its own surface and small marks.

Raw steel has a dark blue grey skin from the mill, with faint streaks and the odd mark from handling. Raw aluminum is a soft, slightly uneven silver. Raw stainless is bright but plain. Designers choose a raw finish when they want the metal to look honest and industrial, or when the piece will be clear coated or painted by someone else.

Raw steel will start to rust if it gets damp, so it needs a clear coat, wax or paint for most interiors. We supply it raw and clean, ready for the finish or coating you choose next.

Suits
Industrial interiors, pieces that will be coated, parts hidden behind a face.
Care
Keep dry. Raw steel needs a protective coat for long use indoors.

Ground

Mill skin and marks taken off with abrasives, leaving a soft swirl or a straight line.

Grinding removes the mill skin and small marks and leaves a fresh metal surface. A random swirl pattern looks hand made and catches light in circles. A straight, linear grind looks calmer and reads well on long trims. Ground steel is bright at first and darkens a little over time.

Ground finishes are also a good base for paint and clear coats. We keep the pattern consistent across a set, and blend edges into the face so the whole piece looks like one surface.

Suits
Feature frames, decorative plates, counters with a hand worked look.
Care
Wipe with a dry or barely damp cloth. Seal ground steel to keep it bright.

Brushed

Fine straight lines in one direction. The everyday choice for stainless and aluminum.

A brushed finish is made with fine abrasive belts or pads drawn in one direction. The result is a soft, satin face with thin parallel lines that hide fingerprints and light scratches. It is the most common finish for interior stainless and aluminum, from kick panels to counter cladding.

On a set of panels, the direction of the brushing is part of the design. We agree it with you, mark it on the parts and keep it the same from piece to piece, so a wall of panels reads as one surface.

Suits
Counter cladding, kick panels, trims, screens and fixture parts.
Care
Clean along the grain with mild soap and a soft cloth. No scouring pads.

Polished

A bright, reflective face that suits small accents and details.

Polishing works through finer and finer abrasives and compounds until the metal reflects like a mirror or a soft sheen. It is beautiful on small accents: a cap, a band in a counter, cut letters on a wall. On large flat panels it shows every ripple and fingerprint, so we often suggest it for details rather than whole surfaces.

Polished parts are wrapped with extra care and handled with gloves until they leave the shop.

Suits
Accents, cut letters, bands and small decorative pieces.
Care
Soft microfiber cloth and a gentle glass cleaner. Avoid anything gritty.

Paint ready

A clean, even surface prepared for your coating shop.

Many designs call for color: a dark matte frame, a soft white screen, a panel matched to a paint chip. We prepare the parts so the coating holds and looks even. That means deburred and softened edges, a cleaned and lightly abraded surface and holes or hidden faces masked if you ask.

The coating itself is applied by the coating shop you choose. We can pack the parts for them directly and include the same labels and packing list.

Suits
Frames and panels in color, screens matched to a palette.
Care
Follows the coating you choose. Ask your coating shop for its care notes.

Choosing by the way a room is used

Start with touch. If people lean on it, grab it or clean it daily, choose brushed stainless or a painted finish. If it sits out of reach as a decorative feature, raw, ground or polished faces are all practical. Then think about light: a polished face changes with every lamp and window, a brushed face glows softly and a dark painted face recedes.

Finally, think about how the piece will age. Brushed and painted surfaces stay much the same for a long time. Ground and raw steel deepen in tone. That change can be part of the charm, as long as everyone expects it.

Ask for a finish sample

Photos and screens never show metal properly. Before a set of parts goes through, we make a small finish plate in the real material, and for important pieces we keep a matching plate in the shop so later batches can be compared side by side.

Brushed stainless counter trim, kick panel and cladding sheets on a felt covered bench

Finishes: common questions

Can you match a finish from another supplier?

Often. Send a sample piece and we make a sample plate for your approval.

Do you apply clear coats or paint?

We prepare surfaces for coating. The coating itself is applied by a coating shop of your choice.

Which finish hides fingerprints most easily?

Brushed stainless and brushed aluminum. Polished faces show the most.

Can one piece have two finishes?

Yes. A brushed face with polished edges, or a ground frame around a brushed panel, are both common requests.

Want to see a finish in real metal?

Ask for a finish sample with your quote. We make a small plate in the material you choose.