From drawing to finished panel in Utah

Every job follows the same six steps, from the first drawing you send to the moment a crate leaves the shop. Here is what happens at each step, what we need from you and what you can expect back.

Paper shop drawing of a panel outline pinned on a layout bench next to a cut steel sample, a tape measure and a ruler
  1. Step 1: You send what you have

    A drawing set, a sketch on squared paper, a photo of an old piece or a sample you want repeated. Add what you know about material, finish, quantity and timeline. The form on our contact page asks for all of it in a few fields, and files and photos can follow by email.

    • Elevations, sections or part drawings in any common format
    • A sample or offcut for finish matching, if you have one
    • Quantities, including spares you might want
  2. Step 2: We read it and ask

    Every request is read by someone who works at the bench. We list the metal parts, check sizes against our equipment, look for details that would be fragile or hard to finish, and write back with questions. This is the step that saves most time later.

    • Which faces are visible and which are hidden
    • What each part sits against and how it is held
    • Which dimensions depend on the room and need confirming
  3. Step 3: A written quote

    Once the questions are answered, you get a written quote listing each part, its material, its finish and the quantity, along with what we need from you and how the parts will be packed. Tolerances that matter to your detail are confirmed here in plain words.

    • Part list with material, finish and quantity
    • Notes on anything that needs your approval
    • How and where the parts will be handed over
  4. Step 4: A sample to approve

    For sets, repeat runs and anything with a visible finish, we make one piece, a short length of trim or a finish sample first. You see it at the shop or we send photos and, if needed, the piece itself. The rest of the run waits for your yes.

    • One panel, a short trim length or a finish plate
    • Pattern, edge and fold checked against the drawing
    • Any change agreed before the run starts
  5. Step 5: Cut, fold, finish

    Parts are cut on the laser table, edges are deburred, sections are formed on the press brake and faces are finished to the approved sample. Brushed grain keeps one direction across a set and film stays on visible faces as long as possible.

    • Laser cutting of outlines, holes and patterns
    • Bending of returns, channels and caps
    • Deburring, grinding, brushing or polishing as agreed
  6. Step 6: Wrapped, labeled, ready

    Finished parts are wrapped, labeled with the names on your drawing and packed in an order that makes sense on the job. You pick up at the shop, or we prepare the crate for the freight carrier you arrange.

    • Each part labeled with its drawing name
    • A simple packing list for sorting
    • Pickup at the shop or a crate ready for freight
Metal worker seen from behind with a face shield down smoothing the edge of a perforated panel, sparks falling to the floor

Working with your team

On larger projects we usually talk to more than one person: the designer who owns the look, the project lead who owns the schedule and the crew who will put the pieces in place. We are happy to keep everyone on one email thread, and we send part drawings and sample photos to whoever needs to approve them.

If something changes in the room, such as a wall that ends up a little longer or a finish that changes after a client meeting, tell us as early as you can. Before cutting, most changes are easy. After cutting, we will tell you plainly what can still be adjusted.

Small jobs are welcome

Not every request is a lobby. A single replacement trim, a handful of cut letters or one sample panel for a client presentation go through the same steps, just faster. If the piece is small, a sketch with dimensions and a photo is usually enough to start.

The process: common questions

How long does a job take?

It depends on the size of the order and what is already in the shop. We give you a realistic timeline with the quote and keep you posted if anything shifts.

Can I visit the shop during the job?

Yes, during shop hours. Call or email first so we can have your parts or samples ready to look at.

Do I have to approve a first piece?

For sets and visible finishes we recommend it. For simple cut parts from a clear file you can skip it if you prefer.

What if my drawing is incomplete?

Send it anyway. Our first reply lists what is missing, and we can prepare part drawings for you to approve.

Ready for step one?

Send what you have. A drawing, a sketch or a photo of a sample is enough to start the conversation.